Inductive sensor NJ4-30GM-N-200
Part number: NJ4-30GM-N-200
0 ... 200 °C (0 ... 392 °F)
Specification
| General specifications | ||
|---|---|---|
| Switching function | Normally closed (NC) | |
| Output type | NAMUR | |
| Rated operating distance | 4 mm | |
| Installation | flush | |
| Assured operating distance | 0 ... 3.04 mm | |
| Reduction factor rAl | 0.15 | |
| Reduction factor rCu | 0.05 | |
| Reduction factor r304 | 0.55 | |
| Output type | 2-wire | |
| Nominal ratings | ||
| Nominal voltage | 8.2 V (Ri approx. 1 kΩ) | |
| Switching frequency | 0 ... 1000 Hz | |
| Hysteresis | ≤ 20 % at 200°C | |
| Suitable for 2:1 technology | yes , Reverse polarity protection diode not required | |
| Current consumption | ||
| Measuring plate not detected | min. 3 mA | |
| Measuring plate detected | ≤ 1 mA | |
| Compliance with standards and directives | ||
| Standard conformity | ||
| NAMUR | EN 60947-5-6:2000 IEC 60947-5-6:1999 | |
| Standards | EN 60947-5-2:2007 EN 60947-5-2/A1:2012 IEC 60947-5-2:2007 IEC 60947-5-2 AMD 1:2012 | |
| Approvals and certificates | ||
| IECEx approval | ||
| Equipment protection level Ga | IECEx PTB 11.0037X | |
| Equipment protection level Gb | IECEx PTB 11.0037X | |
| Equipment protection level Da | IECEx PTB 11.0037X | |
| Equipment protection level Mb | IECEx PTB 11.0037X | |
| ATEX approval | ||
| Equipment protection level Ga | PTB 00 ATEX 2048 X | |
| Equipment protection level Gb | PTB 00 ATEX 2048 X | |
| Equipment protection level Da | PTB 00 ATEX 2048 X | |
| UL approval | ||
| Ordinary Location | E87056 | |
| Hazardous Location | E501628 | |
| Control drawing | 116-0452 | |
| CCC approval | ||
| Hazardous Location | 2020322315002257 | |
| NEPSI approval | ||
| NEPSI certificate | GYJ16.1393X | |
| ANZEx | 18.3018X | |
| Ambient conditions | ||
| Ambient temperature | 0 ... 200 °C (32 ... 392 °F) | |
| Mechanical specifications | ||
| Connection type | cable | |
| Housing material | Stainless steel 1.4305 / AISI 303 | |
| Sensing face | PPS | |
| Degree of protection | IP65 | |
| Cable | ||
| Cable diameter | 4 mm ± 0.2 mm | |
| Bending radius | > 7.5 x cable diameter | |
| Material | FEP | |
| Core cross section | 0.34 mm2 | |
| Length | 5 m | |
| Note | amplifier -25°C...70°C 2 m PTFE cable between amplifier and oscillator | |
| General information | ||
| Use in the hazardous area | see instruction manuals | |
| ECLASS 13.0 | 27274001 | |
| ECLASS 12.0 | 27274001 | |
| ECLASS 11.0 | 27270101 | |
| ECLASS 10.0.1 | 27270101 | |
| ECLASS 9.0 | 27270101 | |
| ECLASS 8.0 | 27270101 | |
| ECLASS 5.1 | 27270101 | |
| ETIM 9.0 | EC002714 | |
| ETIM 8.0 | EC002714 | |
| ETIM 7.0 | EC002714 | |
| ETIM 6.0 | EC002714 | |
| ETIM 5.0 | EC002714 | |
| UNSPSC 12.1 | 39121550 | |